Linux采用双网卡bond、起子接口的方式

# 停掉NetworkManager服务
systemctl stop NetworkManager.service 
systemctl disable NetworkManager.service

# 备份
cp /etc/sysconfig/network-scripts/ifcfg-enp176s0f0{,.bak}
cp /etc/sysconfig/network-scripts/ifcfg-enp176s0f1{,.bak}

# 将网卡协议改为none并设备未开机自启动，并做双网卡配置
sed -i 's/BOOTPROTO=dhcp/BOOTPROTO=none/' /etc/sysconfig/network-scripts/ifcfg-enp176s0f0
sed -i 's/OnBOOT=no/OnBOOT=yes/' /etc/sysconfig/network-scripts/ifcfg-enp176s0f0
echo "MASTER=bond0" >>/etc/sysconfig/network-scripts/ifcfg-enp176s0f0
echo "SLAVE=yes" >>/etc/sysconfig/network-scripts/ifcfg-enp176s0f0

sed -i 's/BOOTPROTO=dhcp/BOOTPROTO=none/' /etc/sysconfig/network-scripts/ifcfg-enp176s0f1
sed -i 's/OnBOOT=no/OnBOOT=yes/' /etc/sysconfig/network-scripts/ifcfg-enp176s0f1
echo "MASTER=bond0" >>/etc/sysconfig/network-scripts/ifcfg-enp176s0f1
echo "SLAVE=yes" >>/etc/sysconfig/network-scripts/ifcfg-enp176s0f1

# 配置网卡bond0
echo "DEVICE=bond0
TYPE=Ethernet
OnBOOT=yes
BOOTPROTO=static" >/etc/sysconfig/network-scripts/ifcfg-bond0

# 写模块文件，bond模式为mode 0
echo "alias bond0 bonding
options bond0 miimon=100 mode=0" >/etc/modprobe.d/bond.conf
# 加载模块
modprobe bonding

# 起子接口bond0.201
echo "DEVICE=bond0.201
TYPE=Vlan
PHYSDEV=bond0
OnBOOT=yes
BOOTPROTO=static
REORDER_HDR=yes
IPADDR=10.10.51.16
GATEWAY=10.10.51.1
NETMASK=255.255.255.0
DNS1=114.114.114.114
DNS2=8.8.8.8
VLAN=yes
VLAN_ID=201" >/etc/sysconfig/network-scripts/ifcfg-bond0.201

# 起子接口bond0.401
echo "DEVICE=bond0.401
TYPE=Vlan
PHYSDEV=bond0
OnBOOT=yes
BOOTPROTO=static
REORDER_HDR=yes
IPADDR=111.20.200.90
GATEWAY=111.20.200.89
NETMASK=255.255.255.0
DNS1=114.114.114.114
DNS2=8.8.8.8
VLAN=yes
VLAN_ID=401" >/etc/sysconfig/network-scripts/ifcfg-bond0.401

# 加载模块并重启主机
modprobe 8021q
reboot

[HH2B108-H01-2-HW9006X-SW001-Eth-Trunk12]display this 
#
interface Eth-Trunk12
port link-type trunk
port trunk allow-pass vlan 201 401
#
return

 # more /etc/modprobe.d/bond.conf
 alias bond0 bonding
 options bond0 miimon=100 mode=4 lacp_rate=1